- Wheel positions: up to 256 per receiver, 160-wheel transporters fitted in production.
- Radio path: 433.92 MHz with repeaters where the load deck blocks the signal.
- Sensor: IP68, -40 to +125 °C internal, band length cut to the rim circumference.
Limitation: Not suitable without the axle drawing: once the load deck blocks the radio path a repeater has to be placed, and that position is decided per trailer.
Products / TPMS
The heavy haulage TPMS solution for multi-axle transport
Heavy haulage moves the load nobody else can carry, on a chassis long enough to attenuate 433.92 MHz before the signal reaches the last axle. The tyre system therefore has one job: import every wheel position into one place, and warn before a tyre is soft enough to matter. This page is how we configure it.
What a heavy haulage TPMS solution has to cover
The words are easy; the constraints are not. A heavy haulage TPMS solution is judged on four things: whether the radio reaches the last axle, whether the driver can act on what the screen shows, whether the data leaves the machine in a format your controller already speaks, and whether the sensors survive the site. Ours measures 0–1400 kPa gauge (100–1500 kPa absolute) at ±7 kPa, up to 256 wheel positions per receiver, 500 ms data cycle on 433.92 MHz, IP68 at the wheel. Repeaters are planned from the chassis layout, not added after the signal fails. On the data side the receiver outputs CAN 2.0B (11- or 29-bit frames) or RS232/RS485, with the frame map or DBC on request. We have instrumented 160-wheel beam carriers; the axle count is a planning input, not something we avoid.
If you are writing the requirement list, the four questions that decide the configuration are in the heavy haulage specification guide; the wheel-plan side is on multi-axle transport TPMS.
FAQ
- Can one receiver cover a 160-wheel heavy haulage combination?
- Capacity, yes — up to 256 wheel positions. Radio, not always: the chassis length decides how many repeaters are needed, which is why we plan from the axle drawing rather than from the wheel count.
- Do you fit external or internal sensors on heavy haulage?
- Internal on this class — strap-mounted or built-in valve, IP68. External units are offered on other machine classes, but on construction and port sites they are exposed and do not survive long.
- How does the data reach our control system?
- The receiver outputs CAN 2.0B at 250 kbps with a 500 ms data period by default, and can also be supplied with RS485, RS232, Modbus RTU or PROFINET. Where the machine has no controller, the same data goes to a 7-inch cab display or to a 4G uplink.
Tell us the application
Send the vehicle, wheel count and where the data must end up. We answer in writing.
Case: a heavy-haulage fleet on multi-axle transporters
What was installed. A heavy-haulage operator running multi-axle transporters and long combinations fitted the system wheel by wheel, with one receiver per machine and repeaters where the load deck interrupted the radio. On a 160-wheel transporter the sensor count is the project - which is why the wheel map is agreed before the hardware list.
The two problems this class has. First, a tyre at the far end of a long combination sits outside the radio range of the cab receiver, so repeaters are part of the layout, not an accessory. Second, the same wheel is used on different routes with different load profiles, so the alarm threshold is set per position, not per vehicle.
What the customer kept. The CAN definitions, the tyre policy and the decision about what a missing reading means. We supplied the sensors, receivers, repeaters and a documented payload.
- Deployed base: more than 600 units in China across mining, port and bus fleets
- Pressure range: 0–1400 kPa gauge (100–1500 kPa absolute); accuracy ±7 kPa
- Ingress protection: IP68 (sensor and receiver); internal sensor −40 to +125 °C
- Wheel positions: up to 256 per receiver; CAN 2.0B, 500 ms data period
- Steel band: 1650 mm for most truck and bus wheels; other lengths cut to the rim circumference
For the trailer side: modular trailers and heavy haulage · beam carriers
If your combination is a B-train or a multi-trailer set, the trailer recognition detail is on the B-train page.
Fleets that swap trailers during the day need trailer identification, not just wheel readings: semi trailer TPMS with automatic trailer recognition.