Материалы / Application

TPMS погрузчика порожних контейнеров: нагрузка и схема

· 8 мин чтения

Empty container handler TPMS: why the load case changes the layout

An empty container handler looks like a reach stacker from a distance. It works differently. The reach stacker takes a loaded container on a spreader and puts weight over the front axle. The empty handler lifts an empty box by its top corner castings and stacks it eight or nine high, which means the machine spends most of its day at low speed with the load held high and to the side, not out in front.

That difference is not cosmetic. It changes which tyres matter, how the wheel load moves, and where a receiver can live without being hit.

What we monitor on an empty container handler

The machine has four wheels, usually 12.00-24 or 14.00-24 in a port fleet, sometimes 16.00-25 on the larger handlers. The front axle carries the mast and the lifted box; the rear axle steers. The tyres that fail first in service are almost always the front pair, and they fail for two reasons that a pressure reading can show early:

  • Heat from repeated short lifts. A handler doing 20 to 30 container moves an hour never reaches highway speed, so the tyre never gets the cooling airflow a truck tyre gets. Pressure rises with temperature and the casing takes it.
  • Load transfer under the mast. When the box is lifted and the boom is tilted back, the front axle load rises sharply and the tyres deflect. A tyre that starts the shift two tenths of a bar low will deflect more under that load, and deflection is what damages the sidewall.

A pressure and temperature reading per wheel, taken every 500 ms by the receiver, shows both trends before the tyre is destroyed.

Where the receiver goes

The receiver needs two things: a clean radio path to all four or six wheels, and a power feed that is not switched off when the machine is parked.

On an empty handler the wheel arches are steel and deep. Mounting the receiver on the mast or under the counterweight looks tidy and performs badly, because the mast blocks the signal to the rear wheels when it is tilted. The positions we have measured as workable are:

1. Under the frame, above the rear axle, pointing forward. The radio path to the front wheels passes under the machine, which is clear of most steel.

2. On the side frame, mid-wheelbase, slightly recessed. Good compromise when the machine works in a stack where the rear is often close to a container.

Both positions need a bracket that survives washdown. A receiver held by cable ties will be gone in a month.

The wheel map is the part people get wrong

Every report a buyer will see later starts with a wheel map: which sensor is which tyre. On an empty handler the trap is the steering axle. The rear axle steers, so "left rear" depends on whether the machine is turning. We name positions by the machine's own forward direction - front left, front right, rear left, rear right - and we write that sentence into the commissioning sheet so that the next shift does not rename them.

If the machine has six wheels, the middle axle is normally the drive axle with dual tyres on each side. Those are the positions where a sensor is hardest to fit, because the valve stem points inward on the inner wheel of a dual pair. On a port machine, with the machine on the ground, that is a job for the tyre bay, not for the driver.

What to check before you quote

Four questions decide the bill of materials on this machine, and each of them has caught us before:

  • Wheel count and dual or single. Four single wheels is one kit; six wheels with duals is a different kit and a different fitting time.
  • Valve type. Port equipment often uses metal clamp-in valves. A sensor that screws onto a rubber snap-in valve will not sit the same way, and the fitting instruction changes.
  • Where the receiver gets power. Ignition-switched is wrong for these machines, because the driver leaves the key off and the handler still needs to report. Take a permanent feed with its own fuse.
  • What the data goes to. If the fleet already has a terminal operating system or a telematics box, the receiver's CAN output goes there; if not, a 4G DTU is the cheaper first step and the CAN interface stays free for later.

We publish the pressure range honestly: 0 to 1400 kPa gauge (100 to 1500 kPa absolute), accuracy plus or minus 7 kPa, and the sensor's own temperature covers -40 to +125 degrees Celsius internally, with the external sensor rated -20 to +85 degrees Celsius. Certification is CE-RED in progress, not finished - if a tender requires a certificate today, say so early rather than at the end.

How this differs from a reach stacker

The reach stacker carries the loaded box on a spreader in front of the machine; the front axle load is high but predictable, and the tyres run warmer because the machine travels further between lifts. The empty handler stacks higher with a lighter box, so the front axle load is lower but the machine is in a container aisle for most of the shift, where the radio path is worst.

That is why the two machines get different receiver positions and different wheel maps even when they share the same sensor. If you buy one kit for both, it will be fitted the same way on both, and one of them will not report reliably.

*Illustrative image - the photographs on the solution page show a machine from the same port-equipment family, not a photograph of the specific model.*

Related: empty container handler TPMS solution, reach stacker TPMS, straddle carrier TPMS, port machinery TPMS.

← Все статьи