Products / TPMS

OTR TPMS for Mining, Port, Construction and Airport Equipment

OTR is one category, not four. A tyre that is worked off the highway has the same job whether the machine is in a pit, on a quay or on an apron; what changes is the axle count, the pressure and the environment. This page is the entry point; the industry pages go deeper.

Direct answers

  • Pressure range: 0-1400 kPa gauge (100-1500 kPa absolute), accuracy ±7 kPa.
  • Enclosure: IP68 on sensor, receiver and repeater - immersion, not just splash.
  • Wheel positions: up to 256 wheel positions per receiver, 1-4 receivers on one machine.
  • Radio: 433.92 MHz, license-free in most markets.
  • CAN output: CAN 2.0B, 250 kbps default, 500 ms data period, 11-bit or 29-bit extended frames.
  • Repeater count is decided from the axle drawing, not from a wheel count formula.

1. What "OTR" covers, and why one page for all four industries

OTR = off-the-road: mining trucks and loaders, port equipment (RTG, reach stacker, empty container handler), construction machinery, and airport ground support equipment. The industries differ in axle count and in what the machine does with the reading, but the four questions that decide the system are identical, which is why one entry page makes sense. The industry pages carry the configuration detail: mining, port machinery, RTG cranes, telehandlers.

2. The four numbers buyers ask for first

NumberValueWhy it decides the project
Pressure range0-1400 kPa gauge (100-1500 kPa absolute), ±7 kPa OTR tyres run from a few bar to well over ten; the top of the range has to cover the machine, not the average
SealingIP68A pit is dust and washdown; a quay is salt water; a splash rating is not enough
Wheel positionsup to 256 per receiver A 160-wheel trailer combination is an address plan, not a sensor count
Data period500 ms Fast enough to see a leak develop, slow enough not to flood the controller

3. How repeater layout is decided

The repeater count follows the chassis drawing. Steel bodies, long trailers and stacked container frames block 433 MHz, so the question is which wheel positions cannot hear the receiver from where it can physically be mounted - and then where a repeater belongs so that they can. That plan is made before the quotation, not in the yard after the first install.

4. Outputs: CAN, RS232, RS485, PROFINET via gateway

The receiver outputs CAN 2.0B (11-bit or 29-bit extended frames, 250 kbps default, 500 ms period) or RS232/RS485; one interface per unit, chosen at the factory. For PROFINET the route is an RS232-to-PROFINET gateway, which is a separate component. Modbus RTU is available as a slave only: your PLC or controller is the master and polls us. The frame map or DBC is supplied on request, so your controller reads the values in the format it already speaks.

OTR tyre pressure: the range first

OTR tyre pressure: 0-1400 kPa gauge (100-1500 kPa absolute) at ±7 kPa, IP68 at the wheel.

On OTR equipment the first question is whether the range covers the machine, not whether the sensor is accurate on a car. We measure 0-1400 kPa gauge (100-1500 kPa absolute) at ±7 kPa, with IP68 at the wheel - a pit, a quay and an apron are all wet, dusty places where a splash-rated sensor is the wrong choice.

Mining dump truck tire pressure: where the range starts

Mining dump truck tyre pressure: the working range starts around 9 bar, covered by 0-1400 kPa gauge.

A mining dump truck does not run at highway pressure: the working range starts around 9 bar (about 900 kPa), which is why a 0-500 kPa sensor is the wrong part for this machine. Our industrial line covers 0-1400 kPa gauge at ±7 kPa, and the receiver reports over CAN 2.0B at a 500 ms period to the machine's controller.

Heavy-duty TPMS sensors: what makes one heavy-duty

Heavy-duty TPMS sensor: IP68 sealing, 0-1400 kPa range, 433.92 MHz, valve or band mounting.

Heavy-duty is not a marketing word here; it is three concrete things: sealing (IP68), range (0-1400 kPa gauge) and mounting that survives the service interval on the machine (valve stem or internal band, whichever the wheel allows). The radio is 433.92 MHz and the battery is chosen to match how often the wheel can realistically be reached, not the other way round.

Where this page ends and the industry pages begin

If the machine is a mining truck, the port pages will not help much and the mining page will; if it is a trailer combination, start with semi trailer TPMS and trailer recognition. This page is the OTR entry point for the machines that do not fit neatly into one industry.

FAQ

Does OTR TPMS cover port equipment as well as mining trucks?
Yes. OTR here means off-the-road: mining, port, construction and airport ground support. The pressure range is 0-1400 kPa gauge and the sensor is IP68.
How many wheel positions can one receiver handle?
Up to 256 wheel positions per receiver; a large machine can use one to four receivers.
Which outputs are available?
CAN 2.0B with 11-bit or 29-bit frames at 250 kbps and 500 ms period, or RS232/RS485; PROFINET via an RS232-to-PROFINET gateway; Modbus RTU as a slave only.

Tell us the application

Send the vehicle, wheel count and where the data must end up. We answer in writing.