Resources / Application

Mining Truck TPMS Repeater Layout and Wheel Plan

· 6 min read

A mine truck is a steel box before it is a vehicle

A 96 tonne rigid haul truck is a working platform: steel chassis, a dump bed that swings, six tyres at 9 bar or more.

That matters for tyre pressure monitoring: the body is the radio obstacle. Sensors transmit at 433.92 MHz, and the dump bed, frame rails and load sit between a rear wheel position and any receiver in the cab. A sensor that reads well in the workshop can drop out on the loaded leg, with the bed up.

The mining truck TPMS overview covers what the system measures; this page is the layout work.

Three reasons a pit is harder than a highway

The body moves. On a highway truck the radio path is fixed; on a haul truck the raised bed is a steel wall between the front and rear wheel groups, and it moves every few minutes.

The wheel count is not four. A rigid truck carries four or six tyres, but a mine combination can present 48 wheel positions on one machine. We have instrumented a 224-wheel machine (28 axles × 8) and a 160-wheel beam carrier; both needed a repeater chain rather than a rule of thumb.

Every tyre removal costs a shift. An internal sensor lives five to six years and cannot be reached without demounting the tyre, so band length and torque must be right the first time. A repeater in the wrong place is cheaper to correct than a sensor in the wrong place.

The four-step method

Same four steps on every machine; the pit makes the inputs harsher.

Step 1 — draw the axle layout

List axles front to rear, wheels per axle, single, dual or super-single tyres, and span lengths. Mark the pivots — the dump hinge, the articulation joint, the fifth wheel — where the radio path changes shape during the cycle. Mark the steel between axles: hoist cylinders, fuel tank, rear axle housing. At 433.92 MHz the signal behaves like light, and every dense object on the path costs link margin.

Step 2 — list the places a receiver may sit

The receiver is IP68 and runs from the vehicle supply at DC 10–30 V, but not every position is available. On a mine truck the permitted places are usually the cab interior, the frame near the first axle, or a protected box behind the cab. Each needs a flat surface, a cable path along the existing loom, and a bracket the mine's engineering authority will accept.

Step 3 — read the blind spots

With the wheel list and permitted mounts, the blind spots appear: positions whose data cannot reach the receiver through steel. Group positions that share a blind spot into a radio zone, and put the boundary where the geometry changes — at the dump hinge, behind the hoist cylinders, at the articulation joint.

Step 4 — count repeaters, then confirm on the machine

One receiver addresses up to 256 wheel positions, so capacity is almost never the reason to add hardware. Radio zones set the repeater count.

A 48-wheel-position example: a rigid truck with a multi-axle trailer, three zones, two permitted mounts. Capacity says one receiver, but the survey shows the rear zone unheard from either mount and the middle zone closing only with the bed down. The answer: two receivers, one per mount, and a repeater at each zone boundary — five to seven units on a machine this length, not one per axle.

Antenna and repeater mounting rules

Mine hardware survives on installation discipline:

  • Keep heat off the antenna and coax. Exhaust, turbo and the hub and brake area run hotter than the electronics are rated for. Route the coax away from the exhaust and never strap it to a hot pipe; −40 to +125 °C is a sensor rating, not a cable rating.
  • Stay off the hydraulic runs. Hoses move, swell and fail; a cable tied to a hose is a cable failure waiting to happen. Keep the runs apart; cross at right angles.
  • Route with the original loom. Reuse clips and grommets, drip-loop every entry, and do not drill structural steel for a radio. Leave slack at the articulation joint and the dump hinge.
  • Mount the repeater on the chassis, not on the moving bed. IP68 covers rain, washdown and dust, not being crushed by a swinging bed.
  • Keep the wash jet off the antenna. High-pressure wash finds any seal that was fitted dry.

Wheel numbering and commissioning

Number positions once, with the customer, and never renumber: axles from the front, left and right, inner and outer. The scheme goes into the delivery document; each sensor ID is bound to its position at commissioning.

Commission in this order: power the receiver on the vehicle supply; bind sensors position by position; walk the machine with the bed down; repeat with the bed up, then loaded and working; record the link check per position and any repeater that moved.

Common mistakes: a wheel map renumbered after a tyre change, a repeater on the moving bed, a sensor on the wrong side, commissioning on a bench instead of the loaded machine.

Rigid truck, wide-body, articulated

Rigid haul truck, 96 to 300 tonnes. Four or six tyres, internal band sensors, receiver in the cab, and the dump bed as the main obstacle. One or two repeaters near the rear axles are usually enough.

Wide-body truck. Lighter and more compact, often on external valve-stem sensors; the radio path is less blocked.

Articulated dump truck. The articulation joint is the radio weak point and where the harness flexes. Repeater on the front frame, receiver at the rear, or the reverse, depending on which mount is permitted; the cable crossing the joint fails first.

The numbers to put in the RFQ

ItemValue
Pressure0–1400 kPa gauge (100–1500 kPa absolute), ±7 kPa
Temperatureinternal −40 to +125 °C; external −20 to +85 °C
Wheel positionsup to 256 per receiver
Radio and sealing433.92 MHz licence-free, IP68
InterfacesCAN 2.0B (11-bit or 29-bit extended frame), RS485 with Modbus RTU, RS232 UART, PROFINET through a gateway
Internal bandcut to the rim circumference — 1650 mm is most common, 2500 mm has been supplied, any length is a cutting step, not a development
CertificationCE in progress

On a J1939 network we work in 29-bit extended frames and have deployed J1939-format message sets in construction machinery integrations with major OEMs; the layout is documented and aligns to your DBC. We hold no J1939 conformance certificate.

What to send us

Send the axle and wheel-position layout, the machine type and tonnage, the permitted receiver and repeater mounts, tyre size and cold inflation pressure, and whether commissioning will be empty or loaded.

We return a sensor count by axle, a receiver and repeater count with mounting points, the controller interface (see the CAN bus TPMS page), and a wheel map template for the numbering above. The mining TPMS range shows the hardware, the product pages list the interfaces, and repeater planning for multi-axle machines covers longer combinations.

Send the drawing on the contact page; the answer is a configuration for that machine, not a brochure.

← All articles

If the whole vehicle layout matters more than the repeater: tyre pressure monitoring for heavy haulage.